How To Set Auto Tune On Dish
Offset dishes may appear to be pointed low towards the horizon, when in fact they are aiming at a much high elevation as shown in the above diagram.
- What Is Auto Tune On Dish Network
- Antares Auto-tune
- Autotune Free Download
- How To Set Auto Tune On Dish Network
Set Your DISH Remote to Satellite Auto Tune August 10th, 2012 A black, blue or snowy screen on your TV2 for your DISH Network duo receiver can be very frustrating, and with your DISH remote it’s entirely preventable. Sep 16, 2013 I finally broke down and called Directv for an answer to this and was told that there is no way to cancel reoccurring manual auto-tunes after you set them. So if you use this feature to set up an auto-tune for a whole season of a show you will have to delete the auto-tune each week when it shows up again and again.
Getting Started
If you've never aligned a dish before, it can be very frustrating, especially if you don't have a signal meter of some sort. You may well end up thinking the receiver is faulty. Digital channels are either 'on' or 'off' and do not fade in or out gradually like analogue signals, further adding to the difficulty. Waving a dish about in the deluded hope that you will somehow find the correct location without either setting the elevation angle or knowing the azimuth angle is a complete and utter waste of time. However, if you follow the steps outlined below you will succeed .. eventually!
1. Attach the F-connectors - Make sure that the cable and F-connectors are properly fitted. The inner core of the coax cable and the outer braid must never come in contact with each other.
2. Set the elevation angle - For the majority of novice satellite users, the satellite they wish to align to is the Astra2/Eurobird cluster at 28 degrees east. This is where Sky, BBC, ITV and C4 are transmitted from. For Ireland, the dish elevation for Astra2 is approximately 22 degrees.
Feb 19, 2014 how to use the auto mix in virtual dj and also some of the effects it has to offer. How to auto tune in virtual dj download. Automixing in Virtual DJ is basically a jukebox function that will attempt to mix two songs together, without you having to do it manually. Discover how it works in this video. Download a free trial of Virtual DJ and start mixing.
Most offset dishes have an elevation scale on the mounting bracket which allows you to adjust the dish to the correct elevation.
For satellites other than Astra2, a list of approximate elevation angles is provided.
Diseqc motors offer a cheap and convenient method for tracking the Clarke Belt with your satellite dish. They can be easily aligned if you take a few initial precautions and follow the steps outlined below.
Installing the Motor
1. Check the pole - ensure that the mounting pole is perfectly straight with a level or inclinometer. If the pole is not level, your dish will not properly track the arc of satellites.
2. Attach the Diseqc motor to the pole - tighten the motor fittings.
3. Set the elevation angle on the motor - the elevation angle on the motor will be based on the latitude of your location. The manual for the motor will tell you what to set this angle to or alternatively, you can use the following table:
What Is Auto Tune On Dish Network
Latitude | Elevation | Declination |
50 | 39 | 6.6 |
51 | 38 | 6.7 |
52 | 37 | 6.8 |
53 | 36 | 6.9 |
54 | 35 | 7.0 |
55 | 7.1 |
4. Attach the dish to the motor shaft - make sure the dish is at right angles to the motor and pole.
5. Set the adjusted declination angle on the dish - your latitude will also determine the declination angle - see above. Most diseqc motors use a special adjusted declination angle formula (based on the tilt of the rotating motor shaft) which will again be specified in your manual. For example, Athlone, with latitude of 53 degrees, will require a declination angle of approximately 7 degrees. A Moteck SG-2100, a common diseqc motor, uses the formula 30 – declination angle. So for Athlone the adjusted declination angle is 23 degrees (i.e. 30-7) when using an SG-2100. This angle can be set according to the markings on the side of the dish.
Antares Auto-tune
Setting the adjusted declination angle
Note: If you have a different model of motor, it will use a different formula for the adjusted declination angle.
This method relies on aligning the motor with true south using a satellite which is positioned at or near true south for your location. In this case, we will use Atlantic Bird 2 located at 8 West as our reference for true south.
1. Slightly loosen the motor fittings - this will enable you to just rotate the motor about the pole. Don't loosen the fittings too much or it will complicate matters.
Autotune Free Download
2. Connect up a satellite meter or alternatively tune the receiver - make sure to tune to an active transponder - the Orbit transponder (11178, H, 27500) is a good choice.
3. Rotate the dish and motor until you see activity on the signal meter - rotate slowly both the dish and motor on the pole until the signal meter is at a maximum. A compass or the position of the sun may be useful in locating true south.
Rotating the dish and motor
Note: For people located on the east coast of Ireland, Atlantic Bird 3 at 5 West may provide better tracking. In that case, use the same procedure as above, but with the France 2 transponder (11591, V, 20000) as your reference.
How To Set Auto Tune On Dish Network
USALS (aka GotoX or Diseqc 1.3) allows you to quickly and accurately align your dish. As most receivers are now USALS compatible, this method provides much better tracking of the Clarke Belt than the 'True South' approach. This is due to the fact that it is more precise to align your dish at the eastern or western extremes of the arc than at the top of the arc (i.e. near true south).
1. Enter you latitude and longitude into the receiver - enter your location coordinates into the the USALS menu of your receiver.
2. Drive the motor to a satellite towards the east or west - select a satellite in the USALS menu and drive or GOTO that satellite. A good choice is Turksat at 42E as it has a strong signal over Ireland.
3. Rotate the dish and motor until you see activity on the signal meter - loosen the pole fittings slightly and rotate slowly both the dish and motor on the pole until the signal meter is at a maximum. If you don't have a signal meter, then watch the quality meter on the satellite receiver which has been tuned to an active transponder. For Turksat, the TRT 1 transponder (11920, V, 24440) is suitable.
4. Tighten the fittings - once the satellite has been found and the signal is at a maximum, tighten the motor fittings to the pole to ensure everything is firmly locked in position.
Once you believe the motor has been properly aligned, it's a good idea to confirm with a few tests. We will use 5 satellites which are spread across the Clarke Belt.
Extreme East Turksat 42E - TRT 1 : 11920, V, 24440
East Hotbird 13E - Al Jazeera : 11034, V, 27500
South Atlantic Bird 2 8W - Orbit : 11178, H, 27500
West Hispasat 30W - Retevision : 12547, V, 30000
Extreme West Intelsat 9 58W - Aastha Channel 2 : 11477, H, 26462
If you run into problems, firstly recheck the pole is level - this is critical for proper tracking. Double check your elevation and declination angles and ensure the motor axis is properly aligned with true south. The following diagram will help you to locate any faults.